Head & Face Protection
24 results(1 filter applied, reset)Legion Safety Products carries a variety of head and face protective gear, including hard hats, hard hat accessories, as well as face shields and visors. Hard hats should generally be worn in areas where workers perform heavy labor and are required in many industries / construction sites where a danger of falling objects is present. Combined with a hard hat accessory, such as a chinstrap and a protective visor, the hard hat becomes a full solution for head and face protection.
Bullard High Density Polyethylene Hard Hat S61R with Ratchet
34 point ratchet type suspension of this hard hat has ¾” nylon straps. Bullard S61R hard hats meet the requirements of ANSI Z89.1-2003 Classes E and G.
$16.90Each
Bullard Classic Full Brim Hard Hat C33R with Ratchet
4Bullard C33R full brim hard hat features 1 inch wide nylon straps on its 6 point ratchet suspension. This comfortable Bullard hard hat exceeds ANSI Z89.2003, Class E and Type I requirements and adjusts vertically.
$24.90Each
Bullard High Density Polyethylene Hard Hat S51R with Ratchet
5The polyethylene hard hat S51R from Bullard has a 4 point ratchet suspension with ¾” nylon straps and height adjustments. These hard hats meet ANSI Z89.1-2003 Class E and Class G requirements.
$14.95EachRefrigiWear 0054 — Hard Hat
5RefrigiWear Hard Hat comes in Blue, Green, Orange, Red, White and Yellow.
$23.90Each
Occunomix TD500 Tuff & Dry Wicking and Cooling Hat w/ Neck Shade
4Cooling relief to your head and back of your neck. 100% Polyester Three Dimensional Honeycomb Knit. Mesh panel for breathability. Roll and snap neck shade.
$20.80Each
CPA Arc Flash Face Shield and Hood Storage Bag SW-SB
This storage bag with drawstring is made to fit an arc flash hood or face shield with an attached hard cap. It will keep your visor from getting scratched or otherwise damaged for best performance.
$23.11Each
Chicago Protective Apparel 7" x 11" Window Aluminum Retainer - 7X11-ALUM-RET
$30.04Each
Bullard Ratchet Suspension RS4RC for Standard Series Hard Hats
The RS4RC ratchet from Bullard was deisgned for standard model Bullard hard hats S51, S61, S62 and S71. It features vertical height adjustments and a 4-point suspension.
$14.95Each
Occunomix 963 Miracool® Terry Lined Ranger Hat
6Ranger hat with terry liner inside works as sweat absorbent when dry and cooling relief when wet. Powered by Miracool® Crystals Technolog. Wide brim works as shade for face and neck.
$14.30Each
Bullard Classic Hard Hat C30R with 6-Point Ratchet Suspension
4Bullard Classic series hard hat C30R features a ratchet suspension with nylon straps and exceeds ANSI Z89.2003, Class E, and Type 1 requirements.
$22.30Each
Bullard Classic Hard Hat C30 with 6-Point Pinlock Suspension
2The C30 Classic series hard hat from Bullard exceeds 1 and Class E requirements. It has a 6-point pinlock suspension with nylon straps and front and rear height adjustments.
$15.40Each
Bullard Ratchet Suspension RS6RC for Classic Series Hard Hats
The replacement suspension for Bullard Classic series hard hats C30 and C33. This ratchet suspension comes with a cotton brow pad and features two front and three rear vertical adjustments.
$15.40Each
Occunomix 880 Clip-On Hard Hat Sweatband, 12 pc pack
2Sweatband with middle layer foam for added comfort. Easily attaches to hard hat suspension with fold over clips. 12 pieces in a pack.
$25.50Pack of 12
MSA V-Gard 500 Hard Hats with 4-PT Fas-Trac Suspension
3V-Gard 500 vented MSA hard cap has a 4 point Fas-Trac suspension with vents that adds comfort to the user. This hard hat exceeds ANSI/ISEA Z89.1-2009 (Class C) standards.
$22.90Each
MSA V-Gard Hard Hats, Full Brim with Fas-Trac Suspension
8Full-brim non-slotted hard hat with Fas-Trac suspension makes it easy to adjust by turning a knob. This hard hat is available in different colors and exceeds ANSI/ISEA Z89.1-2009 (Class E) and CSA Z94.1-2005 (Class E) standards.
$26.50Each
Bullard S62R Hard Hat - High Density Polyethylene Vented with Ratchet
3Low profile, light weight, low center of gravity and 4-point ratched suspension are all features of the ventilated S62R Bullard Hard Hat, which meets Class C requirements.
$20.50Each
MSA V-Gard Hard Caps with Fas-Trac Suspension
7This MSA V-Gard hard cap comes with a Fas-Trac suspension making it easier to adjust by simply turning a knob. This product also exceeds ANSI/ISEA Z89.1-2009 (Class E) and CSA Z94.1-2005 (Class E) standards.
$15.40Each
Bullard SS6 See-Through Sunshield
Bullard SS6 Sunshield features a see through front for overhead visibility. Protects the face, neck and ears from sun exposure and fits on Bullard hard hat styles C33 and S71.
$15.40Each
MSA V-Gard Freedom Hard Cap 10052945 with Fas-Trac Suspension
Freedom series V-Gard Hard Cap are made out of high-quality, wear-resistant materials. It is lightweight and durable and exceeds ANSI/ISEA Z89.1-2009(Class E) and CSA Z94.1-2005(Class E)
$34.90Each
Occunomix SBX100 Value Cellulose Sweatband, 100 pc pack
Anti-mold treated sweatband that provide cooling relief by absorbing sweat. Can be worn under hard hat or welding helmet. 100 pieces in a pack.
$32.30Pack of 100
Occunomix 940-12 Miracool® Neck Bandana 12 pc pack, Assorted
Cotton bandana keeps you cool. Activates in 10-15 minutes after you soak it in cold water. Miracool® Crystals Technology retain moisture. Assortment of 12 pieces.
$19.40Pack of 12
Occunomix 940B24 Miracool® Neck Bandana 24 pc pack
4Cotton bandana keeps you cool. Activates in 10-15 minutes after you soak it in cold water. Miracool® Crystals Technology retain moisture. Bulk of 24 pieces.
$32.70Pack of 24
Chicago Protective Apparel Hard Cap Mounted Faceshield Bracket
3Faceshield mounting brackets for hard hats and caps, available with universal and slotted cap connections. Bracket only, hard caps and visors not included
Currently unavailable
Chicago Protective Apparel Replacement 4.5" x 5.25" Overhood Window - 647-WINDOW
Currently unavailable
