Hard Hats (10)
Bullard Classic Hard Hat C30 with 6-Point Pinlock Suspension
The C30 Classic series hard hat from Bullard exceeds 1 and Class E requirements. It has a 6-point pinlock suspension with nylon straps and front and rear height adjustments.
$15.40Each2
Bullard S51 Hard Hat - High Density Polyethylene with Pinlock
This lightweight S51 hard hat from Bullard features a 4-point pinlock suspension, low profile and a low center of gravity. Meets class E and G requirements.
$8.30Each6
Bullard A1 Hard Hat - High Impact Polycarbonate Alloy with Ratchet
Advent A1 hard hat from Bullard was specially designed for industries like forestry, oil and gas drilling, emergency rescue and others. Features a 8-point suspension and meets Type II, E and G class requirements.
$119.50Each4
Bullard High Density Polyethylene Hard Hat S51R with Ratchet
The polyethylene hard hat S51R from Bullard has a 4 point ratchet suspension with 3/4" nylon straps and height adjustments. These hard hats meet ANSI Z89.1-2003 Class E and Class G requirements.
$14.20Each6
Bullard Classic Full Brim Hard Hat C33R with Ratchet
Bullard C33R full brim hard hat features 1 inch wide nylon straps on its 6 point ratchet suspension. This comfortable Bullard hard hat exceeds ANSI Z89.2003, Class E and Type I requirements and adjusts vertically.
$21.20Each5
Bullard High Density Polyethylene Hard Hat S61R with Ratchet
4 point ratchet type suspension of this hard hat has 3/4" nylon straps. Bullard S61R hard hats meet the requirements of ANSI Z89.1-2003 Classes E and G.
$14.80Each6
Bullard Classic Hard Hat C30R with 6-Point Ratchet Suspension
Bullard Classic series hard hat C30R features a ratchet suspension with nylon straps and exceeds ANSI Z89.2003, Class E, and Type 1 requirements.
$18.70Each6
Bullard A2 Hard Hat - High Impact Polycarbonate Alloy with Ratchet
This Cap-Style A2 hard hat from Bullard features a 8-point suspension, thermoplastic outer shell and provides impact and penetration protection from all directions: top, front, sides and rear.
$128.70Each5
Bullard S62R Hard Hat - High Density Polyethylene Vented with Ratchet
Low profile, light weight, low center of gravity and 4-point ratched suspension are all features of the ventilated S62R Bullard Hard Hat, which meets Class C requirements.
$13.00EachBullard High Density Polyethylene Hard Hat S61 with Pinlock
Hard hat S61 from Bullard features 3 hardness ridges, a 4-point pinlock suspension and vertical adjustments at front and back. It meets ANSI Z89.1-2003 Class G requirements and Class E requirements.
$8.00Each
Bullard Hard Hats with Pinlock and Ratchet Suspensions
Legion Safety has a large selection of Bullard hard hats including the Classic series and other high density polyethylene hard hats and caps. Bullard hard caps and hats are available with ratchet and pinlock suspensions in a variety of styles. We also carry Bullard accessories for the hard hats caps.
A _ hard hat helmet _ is a type of _ head protection gear _ used in various workplace environments, such as some factories, construction areas, archaeological sites and other locations where _ head protection _ is needed to guard against injury by falling objects, impact with other objects, bad weather (especially hail) and electric shock. Unlike motorcycle helmets with padding inside, designed to protect against single impact only (after which the padding needs to be replaced), _ hard hats _ are suspended slightly above the skull – leaving approximately 1 to 1.5 inches of space between the shell and the wearer's head to prevent transmission of impact to the skull. This suspension also serves to spread the weight of the _ hardhat _ helmet over the top of the wearer's head. Some _ hard hat _ models have a round surface and some have a mid-line ridge for better structural integrity.
_ Hard hats _ were originally made from aluminum and later fiberglass, but starting in the 1950s rigid plastic has been the most common material, being cheap and easy to manufacture.
_ Hardhats _ can be fitted with various accessories: safety visors , special ear muffs , helmet flashlight mounts or chinstraps to keep the hardhat from falling off if the wearer bends over. Some _ hard hats _ also have a rolled edge that acts like a rain gutter, allowing water to drain in the front rather than letting the water run down the worker's neck and shoulders.
Legion Safety provides _ hard hats _ in a great variety of colors, which can signify different roles at the work site. For example, a standard yellow color may be worn by regular workers, red by safety inspectors, white by supervisors and blue by visitors.
A light version of a _ hard hat _ helmet is called a _ bump cap _ ; it has a simplified suspension or padding and can only accommodate a chin strap. _ Bump caps _ are used in areas where workers may be in danger of scraping or bumping their heads on equipment or other objects, but they cannot absorb a large impact, such as falling debris or a dropped tool.